路由器的作用、工作原理、发展历史--安全用电-插座行业资讯-插座网

路由器的作用、工作原理、发展历史

2010年01月22日 01:28:56　　　插座网

　　您是否进入基本配置安装,选N
　　First, would you like to see the current interface summary? [yes]: y
　　首先,您是否看一下当前端口状态
　　Any interface listed with OK? value "NO" does not have a valid configuration
　　Interface IP-Address OK? Method Status Protocol
　　FastEthernet0/0unassigned NO unset up down
　　Serial0/0 unassigned NO unset down down
　　FastEthernet0/1unassigned NO unset up down
　　Configuring global parameters:
　　Enter host name [Router]:RouterA
　　输入路由器的名字
　　The enable secret is a password used to protect access to
　　privileged EXEC and configuration modes. This password, after
　　entered, becomes encrypted in the configuration.
　　Enter enable secret: aaa
　　输入密文
　　The enable password is used when you do not specify an
　　enable secret password, with some older software versions, and
　　some boot images.
　　Enter enable password: bbb
　　输入密码(不能和密文相同)
　　The virtual terminal password is used to protect
　　access to the router over a network interface.
　　Enter virtual terminal password: ccc
　　输入虚拟终端的密码(以备远程登录)
　　Configure SNMP Network Management? [yes]: n
　　配置简单网管吗?选N
　　Configure IP? [yes]: y
　　配置IP吗?选Y
　　Configure IGRP routing? [yes]: n
　　配置IGRP路由选择协议吗?选N
　　Configure RIP routing? [no]:
　　配置RIP路由选择协议吗?选N
　　Configure bridging? [no]:
　　配置桥接吗?选N
　　Async lines accept incoming modems calls. If you will have
　　users dialing in via modems, configure these lines.
　　Configure Async lines? [yes]: n
　　配置异步线路吗?选N
　　Configuring interface parameters:
　　Do you want to configure FastEthernet0/0 interface? [yes]: y
　　您是否想配置fastethernet0/0接口?选Y
　　Use the 100 Base-TX (RJ-45) connector? [yes]: y
　　用RJ45的连接器吗?选Y
　　Operate in full-duplex mode? [no]: y
　　选用全双工模式?选Y
　　Configure IP on this interface? [yes]: y
　　在这个接口上配置IP吗?选Y
　　IP address for this interface: 192.168.0.1
　　配置该接口的IP地址(在此地址为192.168.0.1
　　Subnet mask for this interface [255.255.255.0] :
　　配置该接口的子网掩码.(默认的是255.255.255.0,可以手工输入修改)
　　Class C network is 192.168.0.0, 24 subnet bits; mask is /24
　　Do you want to configure Serial0/0 interface? [yes]: y
　　您想配置serial0/0接口吗?选Y
　　Some supported encapsulations are
　　ppp/hdlc/frame-relay/lapb/x25/atm-dxi/smds
　　Choose encapsulation type [hdlc]:
　　选择封装方式(默认的封装方式是HDLC,您可根据与您的路由器相连选用的封装类型来决定用什么样的封装类型
　　No serial cable seen.
　　Choose mode from (dce/dte) [dte]:
　　(因为没有连串口线所以会让您选择设备类型)
　　Configure IP on this interface? [yes]: y
　　(在接口上配置IP)
　　Configure IP unnumbered on this interface? [no]:
　　IP address for this interface: 172.16.0.5
　　配置该接口的IP地址(在此地址为172.16.0.5)
　　Subnet mask for this interface [255.255.0.0] : 255.255.255.252
　　配置该接口的子网掩码.(默认的是255.255.0.0,可以手工输入修改为255.255.255.252)
　　Class B network is 172.16.0.0, 30 subnet bits; mask is /30
　　(以下配置同上)
　　Do you want to configure FastEthernet0/1 interface? [yes]:
　　Use the 100 Base-TX (RJ-45) connector? [yes]:
　　Operate in full-duplex mode? [no]: y
　　Configure IP on this interface? [yes]: y
　　IP address for this interface: 172.16.0.9
　　Subnet mask for this interface [255.255.0.0] : 255.255.255.252 Class B network is 172.16.0.0, 30 subnet bits; mask is /30
　　The following configuration command script was created: